Liftmaster LA412 Solar Powered Residential Gate Operator Instrukcja Użytkownika

LA412 & LA412-S12 VOLT DC SOLAR RESIDENTIAL SWING GATE OPERATOROWNER'S MANUALFOR RESIDENTIAL USE ONLYPlease read this manual and the enclosed

912 gaugewire8 ft.(2.4 m)DUAL GATEEarth Ground Installation (Optional)Solar Panel(Facing South)AntennaHingeWarning SignPost BracketGate BracketGate 1O

Gate MUST be level. Gate and gate post MUST be plumb. Remove ANY/ALL wheels from the bottom of gate.Gate MUST NOT hit or drag across ground.Gate MUST

11INSTALLATION » MANUAL RELEASE + DETERMINE POSITION OF THE PULL-TO-OPEN BRACKET + DETERMINE POSITION OF THE "OPTIONAL" PUSH-TO-OPEN BRACKET

12INSTALLATION » ASSEMBLE GATE POST BRACKET (PULL-TO-OPEN) + ATTACH BRACKETS TO GATE OPERATORAll the illustrations on the following pages display a ty

13INSTALLATION » DETERMINE MOUNTING LOCATION + MEASURING AND MARKING FOR THE GATE BRACKETDETERMINE MOUNTING LOCATIONThe gate post bracket assembly can

141POSITION GATE OPERATOR ON GATENOTE: The post bracket assembly can be mounted several places on the gate post. Refer to page 10 for mounting options

152TEST GATE TRAVELNOTE: If gate does not open and close completely adjust the position of the gate bracket and mark new mounting holes.Ensure that th

16SECURE GATE BRACKET TO GATEThe gate operator (arm) must be level.Some installations may require additional reinforcement be installed on the gate. S

17Knock OutsKnock OutsKnock OutsKnock OutsMOUNT THE CONTROL BOXThe control box MUST be mounted within 5 feet (1.52 m) of the gate operator. Mount the

18INSTALLATION » STANDARD CONTROL BOXINSTALL THE CONTROL BOARDNOTE: Make sure the battery leads are on the left side of the control box and not pinche

1IMPORTANT NOTE• BEFORE attempting to install, operate or maintain the operator, you must read and fully understand this manual and follow all safety

19INSTALLATION » LARGE METAL CONTROL BOX (XLM)MOUNT THE CONTROL BOX (XLM)The control box MUST be mounted within 5 feet (1.52 m) of the gate operator.

20Moving Gate Can CauseInjury or DeathKEEP CLEAR! Gate may move at anytime without prior warning.Do not let children operate the gate orplay in the ga

C71C7ØONOFFLOCK/BIPART DELAY21SET THE LOCK/BIPART DELAY (MODEL LA412-S ONLY)Occasionally in dual gate installations, one gate will need to open first

22CONNECT THE GATE OPERATOR (GATE 2) TO THE CONTROL BOX (MODEL LA412-S ONLY)Before digging, contact local underground utility locating companies. Tren

23JUNCTION BOXThe following items are required to complete the junction box installation:• 4 x 4 Junction Box with 3/4" NPT threaded port holes•

24Remove terminals from operator cable. Strip wires and twist like colored wires together with wire nuts.Wire NutOperator CableExtension CableYellowBl

25SELECT SITE FOR SOLAR PANEL(S)The solar panel(s) must be located in an open area clear of obstructions and shading for the entire day. The solar pan

26SOLAR PANEL INSTALLATION » POSITION SOLAR PANEL(S)POSITION SOLAR PANEL(S)The location of the panel(s) is critical to the success of the installation

27SOLAR PANEL INSTALLATION » INSTALL THE SOLAR PANEL(S)INSTALL THE SOLAR PANEL(S)Solar panel(s) MUST be installed facing south. Use a compass to deter

28CONNECT SOLAR PANEL(S) TO OPERATOR CONTROL BOXOpen the control box cover. Disconnect all power and batteries from the control board. Run the solar p

2SAFETY » SAFETY INSTALLATION INFORMATION 1. READ and FOLLOW all instructions. 2. The gate operator is intended for use with Class I vehicular sw

29When gate is in the desired closed position, press the LEARN LIMITS button.When gate is in the desired position, press the LEARN LIMITS button again

30NOTES:• The gate with the longer travel span (opening) must be set as the primary gate (GATE 1).• If one gate is overlapping the other, the gate t

31Press the GATE 1 left button to open the right operator.SETCLOSEDIAGNOSTICGATE 1FORCEGATE 2SETCLOSELIMITLELIMITWhen the SET CLOSE LIMITS LED blinks,

FORCE ADJUSTMENTThe operator is equipped a with an obstruction current sensing feature. If the gate encounters an obstruction the operator will automa

33TO ADD OR REPROGRAM A REMOTE CONTROL (NOT PROVIDED)Press LEARN XMITTER button and release (LED will light up).Press the remote control button. The L

34OPERATION AND MAINTENANCE » RESET BUTTON + REMOTE CONTROL + SLEEP MODERESET BUTTON The reset button is located on the outside of the control box and

35MANUAL RELEASEIn case of a power failure, the operator can be disengaged from the gate. With an operator, the release action may sometimes feel stif

36TROUBLESHOOTING » WIRING DIAGRAMEDGEEDGE50-220 SAFETY SENSORS50-220 SAFETY SENSORSOROPEN (EXIT LOOP )SINGLE BUTTON (SBC)RESETSTOPSHADOW LOOPINTERRUP

37Your gate operator is programmed with self-diagnostic capabilities. The diagnostic LED will flash a number of times then pause signifying it has fou

38• Power not connected. Make sure the AC/Solar input is connected and that at least one battery is connected with the corresponding fuse intact.•

3SAFETY » GATE CONSTRUCTION INFORMATION1.1 Gates shall be constructed in accordance with the provisions given for the appropriate gate type listed,

39• Antenna not connected. Verify the antenna and coaxial cable are properly connected to the control board.• Remote control not learned. Refer to

1234403542167ITEM PART # DESCRIPTION QTY 1 K1A6426-1 Control Board withMounting Bracket 1 2 K23-19380 Reset Switch 1 3 K74-34392 Antenna

41REPAIR PARTS » HOW TO ORDER REPAIR PARTSHOW TO ORDER REPAIR PARTSOUR LARGE SERVICE ORGANIZATIONSPANS AMERICAFOR INSTALLATION AND SERVICE INFORMATION

423-Button SECURITY✚® Remote Control:Includes visor clip.Protector System® Photoelectric Sensors:The photoelectric sensors are recommendedfor installa

© 2011, The Chamberlain Group, Inc.01-34491J All Rights Reserved1 2 3 4 5 6 77 6 5 4 3 2 1TEMPLATE FOR POST BRACKET MOUNTING

4SAFETY » IMPORTANT SAFETY INFORMATIONINSTALLATIONTo prevent SERIOUS INJURY or DEATH; one or more non-contact sensors shall be located where the risk

5To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:• ALWAYS keep remote controls out of reach of children. NEVER permit c

6INTRODUCTION » OPERATOR SPECIFICATIONS + CARTON INVENTORYCARTON INVENTORYOPERATOR SPECIFICATIONSWarning Signs (2)Moving Gate Can Cause Injury or Deat

7HARDWARE INVENTORYINTRODUCTION » HARDWARE INVENTORY + ADDITIONAL ITEMS FOR PURCHASE + TOOLS NEEDEDNOTE: Hardware quantities shown below are for LA412

8INSTALLATION » OVERVIEW OF TYPICAL INSTALLATIONMoving Gate Can CauseInjury or DeathKEEP CLEAR! Gate may move at anytime without prior warning.Do not