Liftmaster CSW24V High-Cycle Commercial DC Swing Gate Operato Instrukcja Użytkownika

CSW24V™ & CSW24VH™VEHICULAR SWING GATE OPERATORINSTALLATION MANUALYour model may look different than the model illustrated in this manual.UL991com

8INTRODUCTIONOPERATOR SPECIFICATIONS + CARTON INVENTORY & OPERATOR DIMENSIONSOPERATOR SPECIFICATIONSThis model is intended for use in vehicular sw

9INTRODUCTIONFEATURESFEATURESOPERATOR FEATURES• Advanced “Centerpiece” Control Board• AC Surge Protection and EMI Filter Board - Main AC voltage i

10PREPARATIONSITE PREPARATIONCheck the national and local building codes BEFORE installation.GATE CONDUIT & CONCRETE PADGate must be constructed a

11SITE PREPARATIONSAFETYEntrapment protection devices are required to protect against any entrapment or safety conditions encountered in your gate app

12INSTALLATIONSTANDARD INSTALLATION ONLYSTANDARD INSTALLATION ONLYFor compact installation start on page 16.DETERMINE LOCATION FOR CONCRETE PAD AND OP

13CHART INSTALLATIONRefer to the illustration to determine the measurements and location of the concrete pad.INSTALLATIONSTANDARD INSTALLATION ONLY123

14STANDARD INSTALLATION ONLY CONTINUED...CONCRETE PAD AND OPERATOR ATTACHMENTCheck the national and local building codes before installation. NOTE: Wh

15INSTALLATIONSTANDARD INSTALLATION ONLYSTANDARD INSTALLATION ONLY CONTINUED...POSITION THE GATE BRACKETNOTE: It may be necessary to attach horizontal

16INSTALLATIONCOMPACT INSTALLATION ONLY COMPACT INSTALLATION ONLYDETERMINE LOCATION FOR CONCRETE PAD AND OPERATORDO NOT run the operator until instruc

17INSTALLATIONCOMPACT INSTALLATION ONLYCOMPACT INSTALLATION ONLY CONTINUED...SHORTEN THE OPERATOR ARMFor a compact installation the operator arm will

18INSTALLATIONINSTALLATION CONTINUED... INSTALLATION CONTINUED...WELD THE OPERATOR ARMOnce the operator arm measurements are verified:1 Weld the gate

191 Connect the entrapment protection device to the EYES EDGE terminal on the control board: • Close Photoelectric Sensor Entrapment Protection:

20POWER WIRINGWIRINGPOWER WIRINGThis operator can be wired for either 120 Vac or 240 Vac or a solar panel (not provided). Follow the directions accord

21POWER WIRINGWIRINGSOLAR PANEL(S)NOT PROVIDED. SEE ACCESSORIES.Solar Application requirements:• A minimum of four 10W solar panels (Model SOLPNL10W

22J15 PlugJumper Black Wire Red Wire The batteries are charged in the circuit by the integrated transformer. The batteries are for battery backup.1

23CONNECT BATTERIESWIRINGThe batteries are charged in the circuit by the integrated transformer. The batteries are for battery backup or solar install

24DUAL GATES ONLYWIRINGDUAL GATES ONLY WIRELESS DUAL GATESTO ACTIVATE THE WIRELESS FEATURE:1 Choose an operator to be the network primary operator.

25DUAL GATES ONLY CONTINUED...2134Before digging, contact local underground utility locating companies. Use PVC conduit to prevent damage to cables. D

26OPEN limitCLOSE limit!31245To reduce the risk of SEVERE INJURY or DEATH: • Without a properly installed safety reversal system, persons (particula

27FINE TUNE THE FORCEThe FORCE DIAL on the control board is used for fine tuning the force in cases where wind or environmental changes may affect the

1SAFETYWhen you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of serious injury or death if

28ERASE ALL CODES1 Press and release the LEARN RADIO button (operator will beep and green XMITTER LED will light).2 Press and hold the LEARN RADIO

29INSTALL THE COVERFINISH INSTALLATIONTO INSTALL THE COVER1 Remove the operator arm from the output shaft by releasing the handle.2 Align the tabs

30MANUAL DISCONNECTPress the reset switch to RESET/DISCONNECT. Release the handle on the operator arm to allow the gate to be opened and closed manual

31GATE OPERATOR SETUP EXAMPLESADDITIONAL FEATURESGATE OPERATOR SETUP EXAMPLESThe following are example setups for the gate operator. Your specific sit

32CONTROL BOARD OVERVIEWADDITIONAL FEATURESCONTROL BOARD OVERVIEW1 234 56 7891 SET OPEN Button: The SET OPEN button sets the OPEN limit. See Adjust L

33ADDITIONAL FEATURESAOpen Input (& common)(3-Button Control Station, 4 terminals total)Open command - opens a closed gate.Hard open (maintained s

34EXPANSION BOARD OVERVIEWADDITIONAL FEATURESTo AVOID damaging the circuit board, relays or accessories, DO NOT connect more than 42 Vdc (32 Vac) to t

35ComSingle Button Control StationASBC3-Button Control StationBCComOpenCloseStopAUX Relay 2 N.C.ComAUX Relay 2 N.O.AUX Relay 1 N.C.ComAUX Relay 1 N.O.

36FEATURE PRIMARY OPERATOR SECONDARY OPERATORQUICK CLOSE Switch ON OFFANTI-TAIL Switch ON OFFLOW BATT Switch Battery Fail OPEN: OPENBattery Fail CLOSE

37LIMIT SETUP WITH A REMOTE CONTROLADDITIONAL FEATURESLIMIT SETUP WITH A REMOTE CONTROL To set the limits using a remote control, first you will need

2SAFETYUL325 MODEL CLASSIFICATIONSUL325 MODEL CLASSIFICATIONSCLASS I – RESIDENTIAL VEHICULAR GATE OPERATORA vehicular gate operator (or system) intend

38LIFTMASTER INTERNET GATEWAYADDITIONAL FEATURESLIFTMASTER INTERNET GATEWAYTo program the operator to the LiftMaster Internet Gateway:USING THE LEARN

39NON SOLARWIRING DIAGRAMSTo protect against fire and electrocution:• DISCONNECT power and battery BEFORE installing or servicing operator.For contin

40CONTROL BOARD LEDSThe control board is equipped with many LEDs that have a variety of functions. The control board LEDs indicate the status of the o

41INPUT LEDSOPEN INPUT OFF Input inactiveON Input activeBLINK Input active on other operatorCLOSE INPUT OFF Input inactiveON Input activeBLINK Input a

42TROUBLESHOOTING CHARTTROUBLESHOOTINGFAULT POSSIBLE CAUSES CORRECTIONSOperator does not run and diagnostic LED not on.a) No power to control boardb)

43TROUBLESHOOTING CHARTTROUBLESHOOTINGFAULT POSSIBLE CAUSES CORRECTIONSGate opens, but will not close.a) Check DIAGNOSTIC LEDsb) Open control activec)

44TROUBLESHOOTING CHARTTROUBLESHOOTINGFAULT POSSIBLE CAUSES CORRECTIONSAlarm beeps three times with a command.a) Low battery with loss of AC/solar pow

45PHOTOELECTRIC SENSORS (NON-CONTACT)The photoelectric sensors are designed to detect an obstacle in the path of the electronic beam and stop the oper

46REPAIR PARTSNOT SHOWN K94-36540 Wiring Harness with ID resistor assembly K94-36250 Battery Harness (for 7AH batteries) Q103 Swivel Arm Assembl

47REPAIR PARTS12345678910 11121314151617181920212223242526272829

3SAFETYSAFETY INSTALLATION INFORMATIONSAFETY INSTALLATION INFORMATION1. Vehicular gate systems provide convenience and security. Gate systems are co

48NOTES:• Severe or high cycle usage will require more frequent maintenance checks.• It is suggested that while at the site voltage readings be tak

49WARRANTY7 YEAR RESIDENTIAL / 5 YEAR COMMERCIAL CSW24V™ AND CSW24VH™ LIMITED WARRANTYThe Chamberlain Group, Inc. (“Seller”) warrants to the first pur

01-35592G © 2012, The Chamberlain Group, Inc. – All Rights Reserved845 Larch AvenueElmhurst, Illinois 60126-1196

4SAFETYGATE CONSTRUCTION INFORMATIONGATE CONSTRUCTION INFORMATIONVehicular gates should be installed in accordance with ASTM F2200: Standard Specifica

5To prevent SERIOUS INJURY or DEATH from a moving gate:• Entrapment protection devices MUST be installed to protect anyone who may come near a movin

6SAFETYIMPORTANT SAFETY INFORMATIONIMPORTANT SAFETY INFORMATIONINSTALLATIONTo prevent SERIOUS INJURY or DEATH from a moving gate:• Pinch points must

7SAFETYIMPORTANT SAFETY INFORMATIONIMPORTANT SAFETY INFORMATION CONTINUED...ADDITIONAL FEATURESTo prevent SERIOUS INJURY or DEATH from a moving gate:•